Gray Donald M D (34 results)

Soft cover. Condition: Good. No Jacket. 2nd Edition. fat 8vo, pages numbered by sections. 23 sections, 1.5 inches thick. Book has been out in the field, some water stain and soil, plus a little scraping to covers and edges only. Interior is clean, no underlining, notes. Corners thumbed. Weight just over two pounds.…

PAP. Condition: New. New Book. Shipped from UK. Established seller since 2000.

PAP. Condition: New. New Book. Shipped from UK. Established seller since 2000.

PAP. Condition: New. New Book. Shipped from UK. Established seller since 2000.

PAP. Condition: New. New Book. Shipped from UK. Established seller since 2000.

Condition: new.

Paperback. Condition: new. Paperback. The purpose of this research was to evaluate and compare various thermophilic anaerobic digestion processes for meeting U.S. EPA biosolids Class A pathogen standards. The project was split into three phases. Phase 1 screened three bench-scale thermophilic anaerobic process configurations at three different thermophilic temperatures based on their fecal coliform destruction efficiency. All three of the thermophilic process configurations tested were capable of achieving the Class A fecal coliform standard and were included in Phase 2. In Phase 2, bench-scale anaerobic digesters were fed primary sludge seeded with E.coli, helminth ova, poliovirus, and Salmonella to evaluate pathogen destruction. Two process configurations, the thermophilic single-stage and the two-stage mesophilic acid-phase/thermophilic methane-phase system, met Class A requirements at 50oC. In Phase 3, the single-stage thermophilic anaerobic digestion process was compared to the single-stage mesophilic process at full scale (1.5-MG digesters) based on fecal coliform and pathogen destruction, process performance, digested sludge dewaterability, and odor generation.Pathogen destruction and process performance comparisons of the various process configurations are presented for each phase of the study. Based on the fecal coliform data presented here, an empirical model was developed for quantitatively comparing multiple stage and single-stage thermophilic anaerobic digester performance. The model demonstrates that various combinations of thermophilic temperatures, staging, and residence times can achieve the Class A fecal coliform requirement. This study also suggests that anaerobic digesters operating in the lower thermophilic temperature range (approximately 50degreeC) are not only capable of achieving Class A requirements but may also produce digested sludges with less odor and lower volatile solids than digesters operating at higher thermophilic temperatures. The purpose of this research was to evaluate and compare various thermophilic anaerobic digestion processes for meeting U.S. EPA biosolids Class A pathogen standards. The project was split into three phases. Phase 1 screened three bench-scale thermophilic anaerobic process configurations at three different thermophilic temperatures based on their fecal coliform destruction efficiency. All three of the thermophilic process configurations tested were capable of achieving the Class A fecal coliform standard and were included in Phase 2. In Phase 2, bench-scale anaerobic digesters were fed primary sludge seeded with E.coli, helminth ova, poliovirus, and Salmonella to evaluate pathogen destruction. Two process configurations, the thermophilic single-stage and the two-stage mesophilic acid-phase/thermophilic methane-phase system, met Class A requirements at 50oC. In Phase 3, the single-stage thermophilic anaerobic digestion process was compared to the single-stage mesophilic process at full scale (1.5-MG digesters) based on fecal coliform and pathogen destruction, process performance, digested sludge dewaterability, and odor generation. Pathogen destruction and process performance comparisons of the various process configurations are presented for each phase of the study. Based on the fecal coliform data presented here, an empirical model was developed for quantitatively comparing multiple stage and single-stage thermophilic anaerobic digester performance. The model demonstrates that various combinations of thermophilic temperatures, staging, and residence times can achieve the Class A fecal coliform requirement. This study also suggests that anaerobic digesters operating in the lower thermophilic temperature range (approximately 50A0C) are not only capable of achieving Class A requirements but may also produce digested sludges with less odor and lower volatile solids than digesters operating at higher Shipping may be from multiple locations in the US or from the UK, depending on stock availability.…

Paperback. Condition: new. Paperback. Successful operation of the activated sludge process relies heavily on the ability to effectively separate mixed liquor into return activated sludge (RAS) and a high quality final effluent. Solids separation efficiency is dictated in large part by the relative population of floc-forming and filamentous microorganisms present in the activated sludge. During normal operation, mixed liquor will be composed primarily of floc-formers with relatively low levels of filamentous organisms. Some population of filamentous organisms is necessary to promote the formation of larger flocs and prevent development of a "pin-floc" condition, which often results in high effluent turbidities (Jenkins, 2004). However, when conditions favoring the growth of filaments over floc-formers occur, a condition commonly referred to as filamentous "bulking" may occur. Successful operation of the activated sludge process relies heavily on the ability to effectively separate mixed liquor into return activated sludge (RAS) and a high quality final effluent. Solids separation efficiency is dictated in large part by the relative population of floc-forming and filamentous microorganisms present in the activated sludge. During normal operation, mixed liquor will be composed primarily of floc-formers with relatively low levels of filamentous organisms. Some population of filamentous organisms is necessary to promote the formation of larger flocs and prevent development of a "pin-floc" condition, which often results in high effluent turbidities (Jenkins, 2004). However, when conditions favoring the growth of filaments over floc-formers occur, a condition commonly referred to as filamentous "bulking" may occur. Shipping may be from multiple locations in the US or from the UK, depending on stock availability.…

Condition: New. pp. 220 Illus.

Paperback. Condition: New. The purpose of this research was to evaluate and compare various thermophilic anaerobic digestion processes for meeting U.S. EPA biosolids Class A pathogen standards.  The project was split into three phases. Phase 1 screened three bench-scale thermophilic anaerobic process configurations at three different thermophilic temperatures based on their fecal coliform destruction efficiency. All three of the thermophilic process configurations tested were capable of achieving the Class A fecal coliform standard and were included in Phase 2. In Phase 2, bench-scale anaerobic digesters were fed primary sludge seeded with E.coli, helminth ova, poliovirus, and Salmonella to evaluate pathogen destruction. Two process configurations, the thermophilic single-stage and the two-stage mesophilic acid-phase/thermophilic methane-phase system, met Class A requirements at 50oC. In Phase 3, the single-stage thermophilic anaerobic digestion process was compared to the single-stage mesophilic process at full scale (1.5-MG digesters) based on fecal coliform and pathogen destruction, process performance, digested sludge dewaterability, and odor generation. Pathogen destruction and process performance comparisons of the various process configurations are presented for each phase of the study. Based on the fecal coliform data presented here, an empirical model was developed for quantitatively comparing multiple stage and single-stage thermophilic anaerobic digester performance. The model demonstrates that various combinations of thermophilic temperatures, staging, and residence times can achieve the Class A fecal coliform requirement. This study also suggests that anaerobic digesters operating in the lower thermophilic temperature range (approximately 50?C) are not only capable of achieving Class A requirements but may also produce digested sludges with less odor and lower volatile solids than digesters operating at higher thermophilic temperatures.…

Paperback. Condition: New. Successful operation of the activated sludge process relies heavily on the ability to effectively separate mixed liquor into return activated sludge (RAS) and a high quality final effluent. Solids separation efficiency is dictated in large part by the relative population of floc-forming and filamentous microorganisms present in the activated sludge. During normal operation, mixed liquor will be composed primarily of floc-formers with relatively low levels of filamentous organisms. Some population of filamentous organisms is necessary to promote the formation of larger flocs and prevent development of a "pin-floc" condition, which often results in high effluent turbidities (Jenkins, 2004). However, when conditions favoring the growth of filaments over floc-formers occur, a condition commonly referred to as filamentous "bulking" may occur.…

Paperback. Condition: New. The purpose of this research was to evaluate and compare various thermophilic anaerobic digestion processes for meeting U.S. EPA biosolids Class A pathogen standards.  The project was split into three phases. Phase 1 screened three bench-scale thermophilic anaerobic process configurations at three different thermophilic temperatures based on their fecal coliform destruction efficiency. All three of the thermophilic process configurations tested were capable of achieving the Class A fecal coliform standard and were included in Phase 2. In Phase 2, bench-scale anaerobic digesters were fed primary sludge seeded with E.coli, helminth ova, poliovirus, and Salmonella to evaluate pathogen destruction. Two process configurations, the thermophilic single-stage and the two-stage mesophilic acid-phase/thermophilic methane-phase system, met Class A requirements at 50oC. In Phase 3, the single-stage thermophilic anaerobic digestion process was compared to the single-stage mesophilic process at full scale (1.5-MG digesters) based on fecal coliform and pathogen destruction, process performance, digested sludge dewaterability, and odor generation. Pathogen destruction and process performance comparisons of the various process configurations are presented for each phase of the study. Based on the fecal coliform data presented here, an empirical model was developed for quantitatively comparing multiple stage and single-stage thermophilic anaerobic digester performance. The model demonstrates that various combinations of thermophilic temperatures, staging, and residence times can achieve the Class A fecal coliform requirement. This study also suggests that anaerobic digesters operating in the lower thermophilic temperature range (approximately 50?C) are not only capable of achieving Class A requirements but may also produce digested sludges with less odor and lower volatile solids than digesters operating at higher thermophilic temperatures.…

Paperback. Condition: New. Successful operation of the activated sludge process relies heavily on the ability to effectively separate mixed liquor into return activated sludge (RAS) and a high quality final effluent. Solids separation efficiency is dictated in large part by the relative population of floc-forming and filamentous microorganisms present in the activated sludge. During normal operation, mixed liquor will be composed primarily of floc-formers with relatively low levels of filamentous organisms. Some population of filamentous organisms is necessary to promote the formation of larger flocs and prevent development of a "pin-floc" condition, which often results in high effluent turbidities (Jenkins, 2004). However, when conditions favoring the growth of filaments over floc-formers occur, a condition commonly referred to as filamentous "bulking" may occur.…

Condition: New. 2007. paperback. . . . . .

Condition: New. 2004. paperback. . . . . .

Condition: New. pp. 220.

Paperback. Condition: Brand New. illustrated edition. 220 pages. 11.25x8.00x0.50 inches. In Stock.

Condition: New. pp. 220.

Condition: New. KlappentextrnrnSuccessful operation of the activated sludge process relies heavily on the ability to effectively separate mixed liquor into return activated sludge (RAS) and a high quality final effluent. Solids separation efficiency is dictated.

Taschenbuch. Condition: Neu. Neuware - Successful operation of the activated sludge process relies heavily on the ability to effectively separate mixed liquor into return activated sludge (RAS) and a high quality final effluent. Solids separation efficiency is dictated in large part by the relative population of floc-forming and filamentous microorganisms present in the activated sludge. During normal operation, mixed liquor will be composed primarily of floc-formers with relatively low levels of filamentous organisms. Some population of filamentous organisms is necessary to promote the formation of larger flocs and prevent development of a 'pin-floc' condition, which often results in high effluent turbidities (Jenkins, 2004). However, when conditions favoring the growth of filaments over floc-formers occur, a condition commonly referred to as filamentous 'bulking' may occur.…

Taschenbuch. Condition: Neu. Neuware - The purpose of this research was to evaluate and compare various thermophilic anaerobic digestion processes for meeting U.S. EPA biosolids Class A pathogen standards. The project was split into three phases. Phase 1 screened three bench-scale thermophilic anaerobic process configurations at three different thermophilic temperatures based on their fecal coliform destruction efficiency. All three of the thermophilic process configurations tested were capable of achieving the Class A fecal coliform standard and were included in Phase 2. In Phase 2, bench-scale anaerobic digesters were fed primary sludge seeded with E.coli, helminth ova, poliovirus, and Salmonella to evaluate pathogen destruction. Two process configurations, the thermophilic single-stage and the two-stage mesophilic acid-phase/thermophilic methane-phase system, met Class A requirements at 50oC. In Phase 3, the single-stage thermophilic anaerobic digestion process was compared to the single-stage mesophilic process at full scale (1.5-MG digesters) based on fecal coliform and pathogen destruction, process performance, digested sludge dewaterability, and odor generation. Pathogen destruction and process performance comparisons of the various process configurations are presented for each phase of the study. Based on the fecal coliform data presented here, an empirical model was developed for quantitatively comparing multiple stage and single-stage thermophilic anaerobic digester performance. The model demonstrates that various combinations of thermophilic temperatures, staging, and residence times can achieve the Class A fecal coliform requirement. This study also suggests that anaerobic digesters operating in the lower thermophilic temperature range (approximately 50°C) are not only capable of achieving Class A requirements but may also produce digested sludges with less odor and lower volatile solids than digesters operating at higher thermophilic temperatures.…

Paperback / softback. Condition: New. New copy - Usually dispatched within 3 working days.

Paperback. Condition: New. New copy - Usually dispatched within 3 working days.

Condition: New. 2007. paperback. . . . . . Books ship from the US and Ireland.

Condition: New. 2004. paperback. . . . . . Books ship from the US and Ireland.

Paperback. Condition: New. The purpose of this research was to evaluate and compare various thermophilic anaerobic digestion processes for meeting U.S. EPA biosolids Class A pathogen standards.  The project was split into three phases. Phase 1 screened three bench-scale thermophilic anaerobic process configurations at three different thermophilic temperatures based on their fecal coliform destruction efficiency. All three of the thermophilic process configurations tested were capable of achieving the Class A fecal coliform standard and were included in Phase 2. In Phase 2, bench-scale anaerobic digesters were fed primary sludge seeded with E.coli, helminth ova, poliovirus, and Salmonella to evaluate pathogen destruction. Two process configurations, the thermophilic single-stage and the two-stage mesophilic acid-phase/thermophilic methane-phase system, met Class A requirements at 50oC. In Phase 3, the single-stage thermophilic anaerobic digestion process was compared to the single-stage mesophilic process at full scale (1.5-MG digesters) based on fecal coliform and pathogen destruction, process performance, digested sludge dewaterability, and odor generation. Pathogen destruction and process performance comparisons of the various process configurations are presented for each phase of the study. Based on the fecal coliform data presented here, an empirical model was developed for quantitatively comparing multiple stage and single-stage thermophilic anaerobic digester performance. The model demonstrates that various combinations of thermophilic temperatures, staging, and residence times can achieve the Class A fecal coliform requirement. This study also suggests that anaerobic digesters operating in the lower thermophilic temperature range (approximately 50?C) are not only capable of achieving Class A requirements but may also produce digested sludges with less odor and lower volatile solids than digesters operating at higher thermophilic temperatures.…

Paperback. Condition: New. Successful operation of the activated sludge process relies heavily on the ability to effectively separate mixed liquor into return activated sludge (RAS) and a high quality final effluent. Solids separation efficiency is dictated in large part by the relative population of floc-forming and filamentous microorganisms present in the activated sludge. During normal operation, mixed liquor will be composed primarily of floc-formers with relatively low levels of filamentous organisms. Some population of filamentous organisms is necessary to promote the formation of larger flocs and prevent development of a "pin-floc" condition, which often results in high effluent turbidities (Jenkins, 2004). However, when conditions favoring the growth of filaments over floc-formers occur, a condition commonly referred to as filamentous "bulking" may occur.…

Taschenbuch. Condition: Neu. Develop and Demonstrate Fundamental Basis for Selectors to Improve Activated Sludge Settleability | Donald M. D. Gray (u. a.) | Taschenbuch | Final Report Wastewater Treatm | Kartoniert / Broschiert | Englisch | 2007 | Werf | EAN 9781843397526 | Verantwortliche Person für die EU: preigu GmbH & Co. KG, Lengericher Landstr. 19, 49078 Osnabrück, mail[at]preigu[dot]de | Anbieter: preigu.…

Paperback. Condition: New. The purpose of this research was to evaluate and compare various thermophilic anaerobic digestion processes for meeting U.S. EPA biosolids Class A pathogen standards.  The project was split into three phases. Phase 1 screened three bench-scale thermophilic anaerobic process configurations at three different thermophilic temperatures based on their fecal coliform destruction efficiency. All three of the thermophilic process configurations tested were capable of achieving the Class A fecal coliform standard and were included in Phase 2. In Phase 2, bench-scale anaerobic digesters were fed primary sludge seeded with E.coli, helminth ova, poliovirus, and Salmonella to evaluate pathogen destruction. Two process configurations, the thermophilic single-stage and the two-stage mesophilic acid-phase/thermophilic methane-phase system, met Class A requirements at 50oC. In Phase 3, the single-stage thermophilic anaerobic digestion process was compared to the single-stage mesophilic process at full scale (1.5-MG digesters) based on fecal coliform and pathogen destruction, process performance, digested sludge dewaterability, and odor generation. Pathogen destruction and process performance comparisons of the various process configurations are presented for each phase of the study. Based on the fecal coliform data presented here, an empirical model was developed for quantitatively comparing multiple stage and single-stage thermophilic anaerobic digester performance. The model demonstrates that various combinations of thermophilic temperatures, staging, and residence times can achieve the Class A fecal coliform requirement. This study also suggests that anaerobic digesters operating in the lower thermophilic temperature range (approximately 50?C) are not only capable of achieving Class A requirements but may also produce digested sludges with less odor and lower volatile solids than digesters operating at higher thermophilic temperatures.…

Paperback. Condition: New. Successful operation of the activated sludge process relies heavily on the ability to effectively separate mixed liquor into return activated sludge (RAS) and a high quality final effluent. Solids separation efficiency is dictated in large part by the relative population of floc-forming and filamentous microorganisms present in the activated sludge. During normal operation, mixed liquor will be composed primarily of floc-formers with relatively low levels of filamentous organisms. Some population of filamentous organisms is necessary to promote the formation of larger flocs and prevent development of a "pin-floc" condition, which often results in high effluent turbidities (Jenkins, 2004). However, when conditions favoring the growth of filaments over floc-formers occur, a condition commonly referred to as filamentous "bulking" may occur.…